home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
IRIX Patches 1995 December
/
SGI IRIX Patches 1995 Dec.iso
/
relnotes
/
patchSG0000823
/
ch1.z
/
ch1
Wrap
Text File
|
1995-11-17
|
5KB
|
199 lines
- 1 -
1. _P_a_t_c_h__S_G_0_0_0_0_8_2_3__R_e_l_e_a_s_e__N_o_t_e
This release note describes patch SG0000823 to ClearCase
2.0.2 running on IRIX 5.3. This is SGI's release of Atria's
clearcase_p2.0.2-85.
1.1 _S_u_p_p_o_r_t_e_d__S_o_f_t_w_a_r_e__P_l_a_t_f_o_r_m_s
This patch contains bug fixes for ClearCase 2.0.2 on a
system running IRIX 5.3. The software cannot be installed
on other configurations.
1.2 _B_u_g_s__F_i_x_e_d__b_y__P_a_t_c_h__S_G_0_0_0_0_8_2_3
This patch contains fixes for the following bugs in
ClearCase 2.0.2.
+o Contains ClearCase components required to support
ClearCase Attache.
+o cleartool rmtype fails to log rmall operation in
unusual circumstance. Requires users to always say
-rmall if the vob is replicated.
+o Checkin of a DO in the same rule as it is built
confuses view_server.
+o Adjustments in idle specifications when -power is
specified were not being handled correctly. Resulted
in build hosts not being used when they were available.
+o Rules that did not specify a -idle setting were
inheriting a -idle specification from a previous rule
erroneously.
+o Cannot remove reference from a vob to a unix rm'ed
view.
+o cleartool rmtype -rmall would remove all instances of a
type before executing any triggers.
1.3 _S_u_b_s_y_s_t_e_m_s__I_n_c_l_u_d_e_d__i_n__P_a_t_c_h__S_G_0_0_0_0_8_2_3
This patch release includes these subsystems:
+o patchSG0000823.ClearCase_sw.ClearCase
+o patchSG0000823.ClearCase_man.relnotes
- 2 -
1.4 _I_n_s_t_a_l_l_a_t_i_o_n__I_n_s_t_r_u_c_t_i_o_n_s
Because you want to install only the patches for problems
you have encountered, patch software is not installed by
default. After reading the descriptions of the bugs fixed
in this patch (see Section 1.2), determine the patches that
meet your specific needs.
If, after reading Sections 1.1 of these release notes, you
are unsure whether your software meet the requirements for
installing a particular patch, run _i_n_s_t. The _i_n_s_t program
does not allow you to install patches that are incompatible
with your hardware or software.
Patch software is installed like any other Silicon Graphics
software product. Follow the instructions in your _S_o_f_t_w_a_r_e
_I_n_s_t_a_l_l_a_t_i_o_n _A_d_m_i_n_i_s_t_r_a_t_o_r'_s _G_u_i_d_e to bring up the miniroot
form of the software installation tools.
Follow these steps to select a patch for installation:
1. At the Inst> prompt, type
iiiinnnnssssttttaaaallllllll ppppaaaattttcccchhhhSSSSGGGG_x_x_x_x_x_x_x
where _x_x_x_x_x_x_x is the patch number.
2. Initiate the installation sequence. Type
IIIInnnnsssstttt>>>> ggggoooo
3. You may find that two patches have been marked as
incompatible. (The installation tools reject an
installation request if an incompatibility is
detected.) If this occurs, you must deselect one of
the patches.
IIIInnnnsssstttt>>>> kkkkeeeeeeeepppp ppppaaaattttcccchhhhSSSSGGGG_x_x_x_x_x_x_x
where _x_x_x_x_x_x_x is the patch number.
4. After completing the installation process, exit the
_i_n_s_t program by typing
IIIInnnnsssstttt>>>> qqqquuuuiiiitttt
- 3 -
1.5 _P_a_t_c_h__R_e_m_o_v_a_l__I_n_s_t_r_u_c_t_i_o_n_s
To remove a patch, use the _v_e_r_s_i_o_n_s _r_e_m_o_v_e command as you
would for any other software subsystem. The removal process
reinstates the original version of software unless you have
specifically removed the patch history from your system.
vvvveeeerrrrssssiiiioooonnnnssss rrrreeeemmmmoooovvvveeee ppppaaaattttcccchhhhSSSSGGGG_x_x_x_x_x_x_x
where _x_x_x_x_x_x_x is the patch number.
To keep a patch but increase your disk space, use the
_v_e_r_s_i_o_n_s _r_e_m_o_v_e_h_i_s_t command to remove the patch history.
vvvveeeerrrrssssiiiioooonnnnssss rrrreeeemmmmoooovvvveeeehhhhiiiisssstttt ppppaaaattttcccchhhhSSSSGGGG_x_x_x_x_x_x_x
where _x_x_x_x_x_x_x is the patch number.